Mary's Quilting Notes: Thread Catcher Tutorial

I am a bit distractable when I'm making a quilt and I'm not working on the fun part. So this weekend I made a thread catcher...then I decided to make another on because I thought it might be fun to make a tutorial about it. Here is the first one I made in use. I made a few changes the second time I made it and that is the one you will see in the tutorial. It works well with my magnetic pin cushion. I found a tutorial that inspired me this one in particular but I don't use a regular pin cushion, so here we go.

You will need:

lining and outer fabric, a fat quarter will be more than enough of each
a plastic ring cut from a container. Mine happens to be from a quart size greek yogurt container. Cut about 1/2 inch wide
a tile for a weight. I had a square one, so I used it. Another site talked about a subway tile. Whatever you like will work.
non-slip shelf liner

First cut then measure the circumference of the ring you have for the top of the thread catcher. How large you cut your fabric for the bag and liner will be determined by the size of the ring. I sewed everything with a 1/4"seam allowance, so added 1/2 inch to each measurement.

My ring measured 11 3/4 ", so I cut a piece 12 1/4 x 9 "

The pieces for the hangers were originally 3 1/2 x 3 1/2, but I ended up cutting off about an inch, so cut 2 of them 3 1/2 x 2 1/2

The piece for the tile pocket is determined by the size of the tile. You have to remember to make room for the thickness as well, so I just measured around the whole thing, then added about 5/8 inch for seams and a little wiggle room. My tile measured 9 1/2 inches, so I cut a piece 10 1/4 x 5 3/4. That gave me room to tuck the edges in and catch them easily when closing the pocket after the tile is in the pocket.

You'll notice in the picture of the supplies that the tile has tape around the edges. The first thread catcher I made it was difficult to get the tile in the pocket...rough edges, so I covered them with tape and it was much easier to put the tile it.

On the left is a picture of the completed pocket. You'll see that that you have to include the hangers in the pocket. I didn't take a picture but I drew one.

The fabric rectangle is folded in half so it forms a square (sort of) the tabs are pinned between the two layers and the pocket is closed where the tabs are and down one side. The pocket is turned right side out and the side opposite the tabs will be open.

Next the inside and lining side seams should be sewn. Sew the entire length of the outside fabric, for the lining fabric leave about a 4 inch opening in the middle of the seam so when the whole thing is assembled you can turn it right side out. Press the seams open and center them in the middle of the side. Sew the bottom closed and press open. You'll need to clip each end so you can open the seam completely.

Press the side seam so you have a line to match the bottom seam. You need to make box corner as shown to make a flat bottom for the thread catcher. Do this for both the outside and the lining. Cut off the extra piece to remove excess fabric. Here is a great tutorial for box corners--scroll down a bit on the page. The bottom should look like the picture on the right when you're done.

Insert the still unfilled tile pocket into the outside thread catcher. The outside should be wrong side out. Next put the lining in, wrong side out (right sides of the thread catcher will be together, with the tile pocket sandwiched between.

You'll notice in the picture right, that I have about an inch of the hangers showing. I decided 3 1/2" was too long, so I cut them of later. Your hangers will be flush with the top of the thread catcher. Sew all the way around, making sure you catch the hangers fully.

Now it's time to turn the whole thing right side out. Pull the whole shebang through the opening you left in the lining. Once you have it all out, push the outside into the lining. Next you're going to put the ring inside. Push it into the opening, and push the outside through it. You're going to put it up to the top of the bag and pin like crazy to keep it in place. Be sure to have the seam allowance all on the same side.

I sewed using a zipper foot. Because the plastic ring is soft you don't have to worry about a needle breaking. You can see I pinned from the outside, but sewed on the inside.